Knowledge of USB 2.0 is required, see our course reference cours IP2 - USB 2.0
For on-site courses, an additional day covering USB 2.0 fundamentals may be prepended to this USB 3.0 course.
Cours théorique
Support de cours au format PDF (en anglais) et une version imprimée lors des sessions en présentiel
Cours dispensé via le système de visioconférence Teams (si à distance)
Le formateur répond aux questions des stagiaires en direct pendant la formation et fournit une assistance technique et pédagogique
Au début de chaque demi-journée une période est réservée à une interaction avec les stagiaires pour s'assurer que le cours répond à leurs attentes et l'adapter si nécessaire
Tout ingénieur ou technicien en systèmes embarqués possédant les prérequis ci-dessus.
Les prérequis indiqués ci-dessus sont évalués avant la formation par l'encadrement technique du stagiaire dans son entreprise, ou par le stagiaire lui-même dans le cas exceptionnel d'un stagiaire individuel.
Les progrès des stagiaires sont évalués par des quizz proposés en fin des sections pour vérifier que les stagiaires ont assimilé les points présentés
En fin de formation, une attestation et un certificat attestant que le stagiaire a suivi le cours avec succès.
En cas de problème dû à un manque de prérequis de la part du stagiaire, constaté lors de la formation, une formation différente ou complémentaire lui est proposée, en général pour conforter ses prérequis, en accord avec son responsable en entreprise le cas échéant.
Plan du cours
Dual-bus approach
Dual simplex operation, concurrent IN and OUT transactions
Explicitely routed packet traffic instead of USB 2.0 broadcast
Multi-level link power management
New features of data flow model
Robustness
USB 3.0 transaction model
Low power link state transitions
Latency tolerance messaging
Bus interval adjustment
Link-level power management
Super-speed packet format
Bulk transfers, stream ID
Host Controller Driver, purpose of EHCI, xHCI
USB driver
Enumeration
Client drivers
Virtual communication between client drivers and endpoint through communication pipes
Overview of UAS and Video Display new classes
Objectives of OTG specification
Session Request Protoco
OTG 2.0 Host Negotiation Protocol
Impact on PHY layer, voltage thresholds and timeouts
Impact on Link and upper layers
Differences between OTG 2 and OTG 3
Embedded Host
OTG 3 Role Swapping Protocol
Symmetry, SSPC-OTG
Defining who is the default Host through Port capabilities
AC-coupled lines
Receiver detection
Low Frequency Periodic Signaling, utilization of LFPS
Spread Spectrum Clocking
8b10b coding scheme
Elasticity buffer
Pre-emphasis, receiver equalization
Lane polarity inversion detection
Qualifying the physical layer, eye-diagrams
Mathematical processing that must be performed in the oscilloscope
Tests required by the USB Implementer Forum
Loopback BERT
Interface clocking and reset
16- or 32-bit data bus width
Rx polarity
Selecting transmitter voltage levels
Rx status codes
Clock tolerance compensation
Transmitting and detecting LFPS
Low power states
Flow control, header buffer credit
Buffering for data and protocol layer informations
Transmitter timers
Packetization
Specified encoded control sequences
Packet replay in case of error detection
Power-on reset, in-band reset
Link training and status state machine, understanding the main important transitions
Clarifying which transitions are required to enter test modes (loopback and compliance)
Pour vous enregistrer ou pour toute information supplémentaire, contactez nous par email à l'adresse info@ac6-formation.com.
Les inscriptions aux sessions de formation sont acceptées jusqu'à une semaine avant le début de la formation. Pour une inscription plus tardive nous consulter
Ce cours peut être dispensé dans notre centre de formation près de Paris ou dans vos locaux, en France ou dans le monde entier. Il peut aussi être dispensé sous forme d'un cours en ligne, animé par un de nos formateurs.
Nos formateurs sont bilingues et assurent le cours en français ou en anglais.
Les sessions inter-entreprises programmées sont ouvertes dès deux inscrits. Sous condition d'un dossier complet, les inscriptions sont acceptées jusqu'à deux jours ouvrés avant le début de la formation (une semaine pour les cours en présentiel).
Dernière mise à jour du plan de cours : 16 février 2022