| STR8 | STM32MP15 Implementation |
This course describes the STM32MP15x SoC
|
Objectifs
|
- Familiarity with C concepts and programming targeting the embedded world
- Basic knowledge of embedded processors
- The following courses could be of interest:
- Theoretical course
- PDF course material (in English) supplemented by a printed version for face-to-face courses.
- Online courses are dispensed using the Teams video-conferencing system.
- The trainer answers trainees' questions during the training and provide technical and pedagogical assistance.
- Practical activities
- Practical activities represent from 40% to 50% of course duration.
- Code examples, exercises and solutions
- For remote trainings:
- One Online Linux PC per trainee for the practical activities.
- The trainer has access to trainees' Online PCs for technical and pedagogical assistance.
- QEMU Emulated board or physical board connected to the online PC (depending on the course).
- Some Labs may be completed between sessions and are checked by the trainer on the next session.
- For face-to-face trainings:
- One PC (Linux ou Windows) for the practical activities with, if appropriate, a target board.
- One PC for two trainees when there are more than 6 trainees.
- For onsite trainings:
- An installation and test manual is provided to allow preinstallation of the needed software.
- The trainer come with target boards if needed during the practical activities (and bring them back at the end of the course).
- Downloadable preconfigured virtual machine for post-course practical activities
- At the start of each session the trainer will interact with the trainees to ensure the course fits their expectations and correct if needed
- Any embedded systems engineer or technician with the above prerequisites.
- The prerequisites indicated above are assessed before the training by the technical supervision of the traineein his company, or by the trainee himself in the exceptional case of an individual trainee.
- Trainee progress is assessed in two different ways, depending on the course:
- For courses lending themselves to practical exercises, the results of the exercises are checked by the trainer while, if necessary, helping trainees to carry them out by providing additional details.
- Quizzes are offered at the end of sections that do not include practical exercises to verifythat the trainees have assimilated the points presented
- At the end of the training, each trainee receives a certificate attesting that they have successfully completed the course.
- In the event of a problem, discovered during the course, due to a lack of prerequisites by the trainee a different or additional training is offered to them, generally to reinforce their prerequisites,in agreement with their company manager if applicable.
Course Outline
- V7-M Architecture Overview
- Core Architecture
- Harvard Architecture, I-Code, D-Code and System Bus
- Write Buffer
- Registers (Two stacks pointers)
- States
- Different Running-modes and Privileged Levels
- System Control Block
- Systick Timer
- MPU Overview
- Programming
- Alignment and Endianness
- CMSIS Library
- Exception/ Interrupt Mechanism Overview
- Vector Table
- Interrupt entry and return Overview
- Tail-Chaining
- Pre-emption (Nesting)
- NVIC Integrated Interrupt Controller
- Exception Priority Management
- Fault escalation
- Debug Interface
| Exercise: | Becoming familiar with the IDE and Clarifying the boot sequence | |
| Exercise: | Cortex-M4 Mode Privilege | |
| Exercise: | Cortex-M4 Exception Management | |
| Exercise: | Cortex-M4 MPU | |
- V7-A Architecture Overview
- Cortex A7 Overview
- Cortex-A7 Architecture
- Hardware Cache Coherency
- Cortex-A7 Main Features
- System Features
- Multi-processing
- Cache Maintenance
- Cache Coherency Hardware
- Interrupt Distribution
- Power saving Modes
- Memory System Hierarchy
- Software Storage and Upload
- Memory Management Unit
- Generic Interrupt Controller
- Multicore operation
- TrustZone
- Virtualization Extension
- ARM Core Based Architecture
- Description of STM32MP15 SoC architecture
- Clarifying the internal data and instruction paths:
- Bus Architecture
- NIC-400 Network Interconnect AXI-based
- Multi-Layer AHB Interconnect
- Memory Organization
- Embedded Memories: (ROM, SYSRAM, MCU SRAM, Retention RAM
- External Memories: (DDR3/LPDDR2, FMC, QUADSPI, SDMMCx)
- SoC mapping
- Boot Configuration
- Introduction
- BSE Block diagram
- Interface to OTP
- OTP security Mode
- OTP operations
- OTP read
- OTP programming
- OTP permanent write lock
- Scratch registers and Transport key (TK) access
- OTP Mapping
- Power Control
- Power control overview
- Power supplies
- Power supply supervision
- Power management
- Low-Power Modes
- Power control interrupts
- Power Control and TrustZone capability
- RCC Reset and Clock
- RCC overview
- RCC Block diagram
- RCC Reset
- RCC Clock
- RCC interrupts
- Handling dynamic Clock switching
- PLL Programming
- Configuring the sub-system clock
- Clock calibrations using timers
| Exercise: | Configure the system to measure the current consumption in different low-power modes (Cortex-M4) | |
| Exercise: | RTC wakeup timer event / interrupt (Cortex-M4) | |
| Exercise: | Configure the system Clock (SYSCLK) and modify the clock settings in Run Mode (Cortex-M4) | |
- Hardware Semaphore (HSEM)
- HSEM Overview
- Lock procedures
- Clear Procedures
- Interrupts
- Inter-Processor Communication Controller (IPCC)
- IPCC Overview
- Simplex Channel and Half-Duplex channel modes
- IPCC interrupts
- Power pins
- Pinout
- Pin Muxing, alternate functions
- GPIO Module
- Configuring a GPIO
- Speed selection
- Locking mechanism
- Analog function
- Integrated pull-up / pull-down
- I/O pin multiplexer and mapping
- TrustZone security
- System Configuration Controller
- I/O compensation cell
- Ethernet Clock source
- Interrupts
- Nested Vectored Interrupt Controllers (NVIC)
- Global interrupt Controller (GIC)
- Extended Interrupt and event controller (EXTI)
| Exercise: | How to configure the external interrupt lines | |
- Bus Matrix
- DMA
| Exercise: | DMA FIFO mode | |
- Extended TrustZone Protection Controller
- Extended Trustzone architecture and ETZPC
- STM32P15x Security Architecture
- STM32P15x MCU resource isolation
- True Random number generator (RNG)
- Hash processor (HASH)
- Cryptographic Processor (CRYP)
| Exercise: | CRC User Defined Polynomial | |
| Exercise: | How to use ASH peripheral to hash data with SHA-1 and MD5 algorithms | |
| Exercise: | How to use the Cryptographic Processor | |
- DDR3/LPDDR2/LPDDR3 Controller (DDRCTRL)
- DDRCTLR Architecture overview
- Transaction Service Control and QoS
- Power saving
- Address mapper
- DRAM timing parameters
- SDRAM initialization sequence
- Refresh controls
- DDRCTRL Configuration
- TrustZone Address Space Controller for DDR
- DDR physical Interface Control (DDRPHYC)
- DDR performance monitor (DDRPERFM)
- Master Direct Memory Access (MDMA) Controller
- Flexible Memory Controller (FMC)
- Quad-SPI interface
- Delay Block
| Exercise: | Configuring the FSMC controller to access the SRAM memory | |
| Exercise: | QSPI Read Write IT | |
- Open AMP-Overview
- Components in OpenAMP
- Connection between OpenAMP and Libmetal
- How to write a simple OpenAMP application
- CoProSync APIs
| Exercise: | Creating rpmsg channel between Cortex-M4 and Cortex-A7MP (Cortex-M4 side) | |
- Analog-to-Digital (ADC)
- Digital-to-Analog Converter (DAC)
- Digital filter for sigma delta modulators (DFSDM)
- Temperature sensor (TDS)
| Exercise: | ADC Single Conversion Trigger Timer DMA | |
- Independent Watchdogs (IWDG)
- Window Watchdog
- RTC
- Overview
- Functional Description
- RTC low power-modes
| Exercise: | MCU WWDG reset | |
| Exercise: | RTC Alarm | |
- SPI
- USART/UART
- I2C
- Serial audio interface & DPDIF receiver interface
- Management data input/output (MDIOS)
- Secure Digital input/output MultiMediaCard Interface
- FDCAN
- USB OTG
- USB HS PHY controller
- USB EHCI/USB_OHCI
- HDMI-CEC
- Ethernet
| Exercise: | How to handle I2C data buffer Tx/Rx between two boards via DMA | |
- Debug block diagram
- Debug power and clocking
- Security
- Chip Level TAP controller
- Serial wire and JTAG debug port (SWJ-DP)
- Access port
- Cortex-A7 debug
- Cortex-M4 debug
Duration
5 days
Cost
3070 € HT
Calendar
To book a training session or for more information, please contact us on info@ac6-training.com.
Registrations are accepted till one week before the start date for scheduled classes. For late registrations, please consult us.
You can also fill and send us the
registration form
This course can be provided either remotely, in our Paris training center or, worldwide, on your premises.
Scheduled classes are confirmed as soon as there is two confirmed bookings. Bookings are accepted until 2 working days before the course start (1 week for face-to-face courses).
Last update of course schedule: 7 January 2022
Booking one of our trainings is subject to our
General Terms of Sales
