STM32 F0-Series implementation Training | Ac6 Training

ac6-training, un département d'Ac6 SAS
EN
✓EnglishFrench
 
go-up

ac6 › ac6-training › Processors › STM32 › STM32 F0-Series implementation
Inquire
STR4STM32 F0-Series implementation
This course covers STM32F050 and STM32F051 ARM-based MCU family
Objectives
  • This course has 5 main objectives:
    • Describing the hardware implementation and highlighting the pitfalls
    • Describing the ARM Cortex-M0 core architecture
    • Becoming familiar with the IDE and low level programming
    • Describing the units which are interconnected to other modules, such as clocking, interrupt controller and DMA controller, because the boot program generally has to modify the setting of these units
    • Describing independent I/O modules and their drivers.

  • Note that this course has been designed from the architecture of the most complex STM32 F1-Series device, the STM32F051.
  • Consequently, a chapter has been designed by Acsys for each possible integrated IP.
    • According to the actual reference chosen by the customer, some chapters may be removed.

  • Products and services offered by ACSYS:
    • ACSYS is able to assist the customer by providing consultancies. Typical expertises are done during board bringup, hardware schematics review, software debugging, performance tuning.
    • ACSYS has also an expertise in FreeRTOS porting.

A lot of programming examples are provided to help the attendee to become familiar with the topics taught in the course.
Labs included in this course are conducted under the System Workbench for STM32 free IDE. For on-site courses, they can also be compiled and executed under two other IDEs: IAR and Keil
A more detailed course description is available on request at training@ac6-training.com
This document is necessary to tailor the course to specific customer needs and to define the exact schedule.

  • Theoretical course
    • PDF course material (in English) supplemented by a printed version for face-to-face courses.
    • Online courses are dispensed using the Teams video-conferencing system.
    • The trainer answers trainees' questions during the training and provide technical and pedagogical assistance.
  • At the start of each session the trainer will interact with the trainees to ensure the course fits their expectations and correct if needed
  • Any embedded systems engineer or technician with the above prerequisites.
  • The prerequisites indicated above are assessed before the training by the technical supervision of the traineein his company, or by the trainee himself in the exceptional case of an individual trainee.
  • Trainee progress is assessed by quizzes offered at the end of various sections to verify that the trainees have assimilated the points presented
  • At the end of the training, each trainee receives a certificate attesting that they have successfully completed the course.
    • In the event of a problem, discovered during the course, due to a lack of prerequisites by the trainee a different or additional training is offered to them, generally to reinforce their prerequisites,in agreement with their company manager if applicable.

Course Outline

  • ARM core based architecture
  • Description of STM32F050X and STM32F051X SoC architecture
  • Clarifying the internal data and instruction paths: AHB-lite interconnect, peripheral buses, AHB-to-APB bridges
  • Private Peripheral Bus (PPB)
  • Integrated memories
  • SoC mapping
  • V6-M core family
  • Core architecture
  • Programming
  • Exception behavior, exception return
  • Basic interrupt operation, micro-coded interrupt mechanism
  • Acsys covers 3 IDEs: Keil, IAR and GCC / Lauterbach
  • Thus the customer has just to indicate which one he has chosen
    • Getting started with the IDE
    • Parameterizing the compiler / linker
    • Creating a project from scratch
    • C start program
  • Debug interface
  • Programming
  • Power control
  • Reset
  • Clocking
  • Low power modes
  • Bus matrix
  • DMA
  • Power pins
  • Pinout
  • GPIO module
  • System configuration controller
  • External Interrupts
  • Embedded flash memory
  • Internal SRAM
  • Advanced-control timers TIM1
  • General-purpose timers (TIM2 and TIM3)
  • General-purpose timers (TIM14-17)
  • Basic timers (TIM6)
  • Real Time Clock
  • Independent Watchdog
  • Window Watchdog
  • 12-bit Analog-to-Digital Converter and Programmable Gain Amplifier
  • 12-bit Digital-to-Analog Converter
  • Comparator
  • CRC calculation unit
  • SPI
  • SPI in I2S mode
  • USART
  • I2C
  • Touch sensing interface
  • HDMI-CEC
Duration
4 days
Inquiry

This course can be scheduled upon request. Click the 'Inquire' button to contact us.

More

To book a training session or for more information, please contact us on info@ac6-training.com.

Registrations are accepted till one week before the start date for scheduled classes. For late registrations, please consult us.

You can also fill and send us the registration form

This course can be provided either remotely, in our Paris training center or worldwide on your premises.

Scheduled classes are confirmed as soon as there is two confirmed bookings. Bookings are accepted until 1 week before the course start.

Last update of course schedule: 23 February 2026

Booking one of our trainings is subject to our General Terms of Sales

Related Courses