ac6-training, un département d'Ac6 SAS
EN
✓EnglishFrench
go-up

ac6 › ac6-training › AT91SAM7SE microcontroller implementation
Inquire
AT1

AT91SAM7SE microcontroller implementation

This course covers AT91SAM7SE ARM based microcontroller

Objectives

  • The course details the hardware implementation of the AT91SAM7 microcontrollers.
  • The boot sequence and the clocking are explained.
  • Practical lab on integrated peripherals are based on I/O functions provided by Atmel.
  • The course focuses on the low level programming of the ARM7TDMI core.
  • The course provides examples of internal peripheral software drivers.

  • Note that ACSYS does not sell emulation probes and IDEs. Consequently this course has not been designed to convince attendees to buy a particular IDE. The unique objective consists in providing sufficient knowledge to attendees so that they can successfully design a system based on AT91SAM7.

  • This course has been delivered several times to companies developing embedded systems, such as badges and RF equipments.
A lot of programming examples have been developed by ACSYS to explain the boot sequence, the vector table and the operation of embedded peripherals.
•  They have been developed with 2 different IDEs : Keil and IAR.
•  Consequently for on site course, it is up to the customer to select the IDE under which labs will be run.
A more detailed course description is available on request at training@ac6-training.com
  • This course provides an overview of the ARM7TDMI core. Our course reference R1 - ARM7/9 implementation course details the operation of this core.
  • The following course could be of interest:
    • USB Full Speed High Speed and USB On-The-Go, reference IP2 - USB 2.0 course
  • Theoretical course
    • Printed and PDF material in English.
    • Trainer assistance throughout.
  • Each session starts with a trainee check-in.
  • Any embedded systems engineer or technician with the above prerequisites.
  • Prerequisites are checked before the course starts, against the prerequisites published on this page.
  • Throughout the course, learning is assessed continuously: end-of-section quizzes and direct observation by the trainer.
  • At the end of the course, each participant receives a training completion certificate.

Course Outline

  • ARM core based architecture
  • APB internal busses
  • The main three blocks : platform, core and input / output peripherals
  • Operating modes
  • ALU data path
  • ARM vs Thumb instruction sets, interworking
  • Access to memory-mapped locations
  • Stack management
  • Benefits of condition set capability in ARM state
  • C-to-Assembly interface
  • Exception mechanism, handler table
  • Power supplies, internal regulator
  • Clock generator
  • Reset controller
  • SAM-BA default boot program
  • Memory controller
  • Internal high-speed flash
  • External Bus Interface
  • Power management controller
  • Advanced interrupt controller
  • Parallel input / output controller
  • Peripheral DMA controller
  • Timers
    • Periodic Interval Timer
    • Windowed Watchdog
    • Real-time timer
    • 3-channel timer / counter
    • 16-bit PWM controller
  • Analog-to-Digital Converter
    • 8-channel 10-bit ADC
    • Conversion trigger
    • ADC timings
  • 2-wire interface
    • I2C protocol basics
    • Transmit and receive sequences
  • SPI
    • SPI protocol basics
    • External chip-select
    • Transfer sequence
  • USART
    • Individual baud rate generators
    • IrDA modulation / demodulation
    • Support for Smart Card
    • RS485 support
  • Synchronous Serial Controller
    • I2S analog interface support
    • Time Division Multiplexed support
    • High speed continuous data stream capabilities
  • USB
    • Full speed operation
    • Endpoint configuration
Duration
4 days
Inquiry

This course can be scheduled upon request. Click the 'Inquire' button to contact us.

Pricing

Courses are quoted individually, with no list price. The price depends on the duration, the number of participants, the delivery mode and the technical resources provided.

For more information on our pricing, see more.

More

To book a training session or for more information, please contact us on info@ac6-training.com.

Registrations are accepted till one week before the start date for scheduled classes. For late registrations, please consult us.

You can also fill and send us the registration form

This course can be provided either remotely, in our Paris training center or worldwide on your premises.

Scheduled classes are confirmed as soon as there is two confirmed bookings. Bookings are accepted until 1 week before the course start.

Last update of course schedule: 27 June 2026

Booking one of our trainings is subject to our General Terms of Sales

On the same topic:

Yocto or Buildroot: how to choose for your embedded Linux project